Engineering

United States Excelling Tender

📄 Tender ID: 462309392 📅 Published: 13 May 2021

📋 Tender Overview

Started by Earl Reichel 55 years ago Soils Engineering Services Inc. bought their first auger drilling rig in 1968 to provide drilling as part of their geotechnical engineering. As the drilling division expanded they added environmental sampling to the services they provided others.During 1980s when environmental sampling was booming in Wisconsin due to state requirements for gas stations to upgrade their underground storage tanks we used a hydraulic hammer on our auger rigs for direct push sampling Duane Reichel owner said. All along I followed the progress of Geoprobe equipment and improvements.Once his Dad Earl retired in 1993 Duane became partner in the company and then sole owner in 2018. He then sold a couple of their auger drill rigs and invested in a 7822DT.We werent really equipped well for environmental direct push sampling and we also had a need for a smaller geotechnical rig Reichel said. We looked at auger rigs and typically they are designed more for geotechnical work than environmental. We wanted a rig that could excel at both geotechnical and environmental sampling.After seeing the website videos and literature they were sold on getting a Geoprobe. Further solidifying their decision was their clients asking for Geoprobe rather than direct push. The name itself was a selling point. VersatilityWe call it the Swiss Army Knife. Multipurpose good for direct push auger rock coring Reichel said. All of our other auger rigs have 8000 to 14000 lbf of torque with the exception of the skid rig which has less than 2000 lbf of torque. I was looking for something with torque in between those two ranges. I wanted to have a wide range of capabilities in our fleet.A lot of their geotechnical and environmental work in Madison and southern Wisconsin has been in developed areas or house additions or new houses on lakefront parcels where there is limited access or limited heights.We bought a small skid rig before the 7822DT for working in limited heights and we are able to use the 7822DT in most areas that the other small rig can go but we appreciate the higher torque on the 7822DT Reichel said. Its nice to have a smaller profile. We can adjust the height of the mast for ceilings power lines or tree canopy. Its easier to use the smaller profile rig when doing an auger or rotary boring next to a building rather than struggling to jockey a larger rig into tight spaces or have to locate the boring somewhere other than where the client wants it.Reichel admits there was an adjustment period but the benefits are great.Theres a learning curve for us going from purely auger rigs to Geoprobe. Its a different set up but nicer. We can angle the mast to get tooling vertical or adjust the tower to compensate to maintain a vertical hole or to work with a hole that is a bit off vertical Reichel said. The engine RPM changes according to demand making the rig quieter since its not always running full bore. Combined with the rig engine being smaller than an auger rig were saving on fuel costs for operating and transporting it.Having had previous direct push experience using another manufacturers rig and tooling Reichel can clearly see the benefits of the combination 7822DT.The other rig and tooling was doing the job but not as efficiently. With Geoprobe its all inclusive from tooling to rig so its thought out multiple ways Reichel said. Theres not a lot to find to complain about. If there are issues with tooling or the rig the engineering team is willing to look at things and rectify the issue.AccessibilityThey appreciate having a single rig to do multiple things coring concrete mud rotary rock coring and direct-push environmental sampling and upgraded to do CPT work and all the places they can use it.We can go offroad quite a bit. We dont have to use as much matting as we would with our truck rig or even our low-pressure rubber tire rigs Reichel said. When drilling at existing houses where they have failing slopes or where the lake shore property has erosion they arent damaging existing lawns.We were able to get to sites where we wouldnt have been able to with our larger rigs Reichel said. We can sneak in between houses without other equipment as we would with our skid rig since the 7822DT is self-contained.Expanding MarketA recent job took them inside to investigate proposed improvements to the south end zone seating for the University of Wisconsin-Madison Camp Randall stadium. They drilled soil borings below the bleacher seating in the concession area. The footprint of the 7822DT meant they could handle the sloping ceiling above to get the rig closer to the wall with more working height. The rubber tracks meant they werent marking up the concrete and because the rig is self-contained they didnt have a lot of engine exhaust or noise. We wouldnt have been able to do the geotechnical sampling if we hadnt had the 7822DT. We mud rotary drilled the borings to allow the use of a pressure meter for testing the soils for soil bearing capacity and settlement Reichel said. Our other auger rigs are wider and longer than the 7822DT and they would have been more difficult to maneuver in the concession area. The 7822DT allows us to turn in place and to get closer to obstructions.This is just one example of how the versatility and accessibility of the 7822DT has helped Soils and Engineering expand their market.We are able to go after more jobs than before or dont have to subcontract some drilling because we cant get on site. Were looking forward to seeing what other challenges we can put the rig up to Reichel said. We havent been on a barge yet with the 7822DT. But the lightweight and small footprint means we wont need as big a barge versus a conventional drill rig yet we still have direct push augering and rotary capabilities in a smaller footprint.

🔍 Key Information

📄
Tender Reference No.
462309392
📅
Publication Date
13 May 2021
🌐
Sector
Engineering
📝
Notice Type
News
📍
Location
United states

📁 Documents & Downloads

No documents found

🏷️ CPV

No CPV found

Need help with this bid?

Our bid experts can help you find, evaluate & win more tenders.

🎧 Talk to Bid Expert
🕒 Submission deadline
0
days remaining · 13 May 2021
🔔 Set Alert

🧭 Quick Facts

Authority N/A
Country United states
State / UT N/A
Tender Type Procurement News
Currency N/A
Similar Tenders
Loading similar tenders…