Energy, Power and Electrical

Germany Charging Infrastructure Tender

📄 Tender ID: 513212880 📅 Published: 18 Jan 2025

📋 Tender Overview

At the same time, the system is very efficient and can be flexibly applied to charging stations of different sizes and different vehicle types. A demonstrator of one charging point can be viewed at the Fraunhofer Energy Alliance booth at the E-World from 11-13 February in Essen, Germany (hall 5, D 126).

As the number of e-vehicles increases, so does the need for fast-charging stations that simultaneously serve many vehicles in the same way as typical filling stations do today. This requirement is particularly relevant along freeways, but also in urban parking garages and parking lots. The average output of a fast-charging system for a car is 150 kW. This rises to 350 kW for buses, vans and small trucks, with higher charging capacities expected in the future. Since electric charging is slower than the refuelling process, around 15 to 25 charging points will be needed in the future instead of the typical eight gas pumps at filling stations today. Together these charging points will draw around 1.5 to 3.5 megawatts of power when fast charging in parallel, which means that future fast-charging stations can no longer be supplied via the low-voltage grid. Even if the charging station is underutilized, the power required would exceed 300 kW. Also the power distribution within the charging station or parking lot should not be distributed in the low voltage grid. This would lead to big installation costs and large energy losses in cables, due to the long cable runs of e.g. 100 meters or more for 25 parking spaces, coupled with the high powers.

The power electronic system developed in the project with the partners Sumida Components & Modules GmbH, Infineon Technologies AG and AEG Powersolutions GmbH therefore relies on a medium voltage grid that is adapted to a voltage of 1500 VDC using a rectifier. The higher voltage level enables a higher output at the same current without necessitating the cable cross-section to be increased. The significantly lower copper consumption that results contributes significantly to environmental protection and resource conservation. The value of 1500 VDC was selected for this unit, as it is the boundary limit of the low voltage standard. Above this value, other standards would apply.

Modular approach for charging stations of different sizes
An electrically isolated converter couples the direct current (DC) distribution network to the vehicle battery and controls the fast-charging process. The DC converters, each with an output of 175 kW, are designed so that they can easily be connected in parallel in the system. This modular approach makes it possible to build charging stations with lower power charging points for cars and higher power charging points for trucks.

In contrast to domestic wall boxes, charging stations must be highly compatible for different vehicle types. The concept of a central rectifier and a 1500 V DC distribution, which was developed in the project, is advantageous in that the grid connection components (transformer and rectifier) can be dimensioned and scaled more independently of the charging electronics. In view of the high demand for power electronics and components, like cables and transformers, the material requirements for this system are significantly reduced compared to other current solutions.

For an uncomplicated charging process, the charging station should be fully compatible with the CCS1 and CCS2 standards, which are widely established in Europe for vehicle currents up to 500 amperes and voltages up to 1000 volts. In addition, the concept also supports the Megawatt Charging System (MCS) standard. A second converter module is planned to address this. For this variant only a few components need to be adapted.

"The topology we developed in this project finds applications not only in charging stations but also for its integration in renewable hybrid power plants or stationary battery storage systems," explains Andreas Hensel, group manager of High Power Electronics and System Technology at Fraunhofer ISE.

🔍 Key Information

📄
Tender Reference No.
513212880
📅
Publication Date
18 Jan 2025
🌐
Sector
Energy, Power and Electrical
📝
Notice Type
News
📍
Location
Germany

📁 Documents & Downloads

No documents found

🏷️ CPV

No CPV found

Need help with this bid?

Our bid experts can help you find, evaluate & win more tenders.

🎧 Talk to Bid Expert
🕒 Submission deadline
0
days remaining · 18 Jan 2025
🔔 Set Alert

🧭 Quick Facts

Authority N/A
Country Germany
State / UT N/A
Tender Type Procurement News
Currency Vijay98
Similar Tenders
Loading similar tenders…